追求卓异品质,打造民族精品。欢迎您来到高品质金刚石压头、硬度计知名生产企业—莱州市试验机金刚石工具厂
金刚石压头
资料更新中,敬请期待。...
HTS-1000A 型数显便携硬度计
HTS-1000A型数显里氏硬度计是采用美国技术,与清华大学合作研制的多功能便携式测试仪器。本机制作精...
洛氏金刚石压头
【莱金】是莱州市试验机金刚石工具厂精研生产的金刚石压头产品注册商标。厂家是取得金刚石压头计...
HVG-1000AXYT型微机控制显微
HVG-1000AXYT型微机控制显微硬度CCD图像分析系统适用于金属材料和金属部件的维氏硬度的测试,因而在...厂家电话:0535-2215886
0535-2263683
0535-2265113
华东分部:0571-85375562
外贸联系:13693019205
以一定的载荷(一般3000kg)把一定大小(直径一般为10mm)的淬硬钢球压入材料表面,保持一段时间,去载后,负荷与其压痕面积之比值,即为布氏硬度值(HB),单位为公斤力/mm2(N/mm2)。
2.洛氏硬度(HR)
当HB>450或者试样过小时,不能采用布氏硬度试验而改用洛氏硬度计量。它是用一个顶角120°的金刚石圆锥体或直径为1.59、3.18mm的钢球,在一定载荷下压入被测材料表面,由压痕的深度求出材料的硬度。根据试验材料硬度的不同,分三种不同的标度来表示:HRA:是采用60kg载荷和金刚石压头押入器求得的硬度,用于硬度极高的材料(如硬质合金等)。HRB:是采用100kg载荷和直径1.58mm淬硬的钢球,求得的硬度,用于硬度较低的材料(如退火钢、铸铁等)。HRC:是采用150kg载荷和金刚石压头押入器求得的硬度,用于硬度很高的材料(如淬火钢等)。
With a certain load (generally 3000kg), the hardened steel ball of a certain size (generally 10mm in diameter) is pressed into the surface of the material and kept for a period of time. After the load is removed, the ratio of the load and the indentation area is the Brinell hardness value (HB), and the unit is kg force /mm2(N/mm2).
2. Rockwell Hardness (HR)
When HB>450 or the sample is too small, the Brinell hardness test should not be used, but rockwell hardness measurement. It is to use a diamond cone with a top Angle of 120° or a steel ball with a diameter of 1.59 or 3.18mm to press into the surface of the measured material under a certain load, and the hardness of the material can be calculated by the depth of the indentation. According to the hardness of test materials, there are three different scales: HRA: hardness obtained by 60kg load and diamond indenter, used for materials with high hardness (such as hard alloy, etc.). HRB: the hardness is obtained by using 100kg load and 1.58mm diameter hardened steel ball, used for low hardness materials (such as annealed steel, cast iron, etc.). HRC: hardness obtained by 150kg load and diamond indenter for high hardness materials (such as hardened steel, etc.).