追求卓异品质,打造民族精品。欢迎您来到高品质金刚石压头、硬度计知名生产企业—莱州市试验机金刚石工具厂

新闻资讯

热销产品

近期案例

  • HV-1000A型图像处理显微硬度计安装案例
  • HV-1000ASCCT显微图像处理系统案例
  • 200HVS-10型小符合维氏硬度计安装顺利完
  • MP-2T、XQ-2B等金相制样设备安装案例
  • MRV-320型孔隙率检测显微镜案例
  • 5公斤小负荷维氏硬度计(带电脑图像分析系
  • ZXQ-5型自动镶嵌机
  • 安装调试HV-1000ACCT图像处理系统
  • HVS-1000ATXY型自动步进平台显微硬度计
  • 系列硬度计安装调试
  • MRG-480型研究级金相显微镜图像处理系统
  • HBS-3000型精准稳固型数显布氏硬度计顺
  • HRS-150数显洛氏硬度计安装案例
  • HV-1000Z型自动转塔显微硬度计
  • 调试安装MP-2CE型金相磨抛机
  • 数显洛氏硬度计测试精度高、重复性好,获
  • 320HBS-3000型数显布氏硬度计安装实例
  • HV-1000ASCCT显微图像处理系统案例
  • 4XC型金相显微镜(带电脑及金相分析系统)
  • FR-3e型数显洛氏硬度计
  • P-2G型金相抛光机
  • 200HRS-150数显洛氏硬度计安装实例
  • HV-1000ASCCT图像处理显微硬度计安装案
  • MRG-480型金相显微镜案例
  • 220HBS-3000型数显布氏硬度计安装实例
  • HV-1000ACCT图像处理显微硬度计安装案例
  • 220HBS-3000CCD型图像处理数显布氏硬度
  • 数显全洛氏硬度计
  • P-2型金相试样磨抛机安装完成
  • HBS-3000型数显布氏硬度计安装实例
  • HV-1000ASCCT显微图像处理系统案例
  • HV-50ASCCT图像处理维氏硬度计安装培训
  • 200HRS-150数显洛氏硬度计安装案例
  • HV-1000A(配图像处理系统)显微硬度计案例
  • 大型250金相切割机的安装调试后,顺利通过
  • TH140型里氏硬度计案例
  • QGY-250型金相试样切割机安装案例
  • 客户采购我司提供的金相制样设备,合理地
  • 图像处理显微硬度计1套,调试安装完成,顺利
  • 220HBS-3000CCD型图像处理数显布氏硬度
  • HVG-30型高端数显维氏硬度计安装实例
  • 国家文教用品质量监督检验中心-HV-1000
  • 200HVS-10型小符合维氏硬度计图像处理系
  • HBS-3000型数显布氏硬度计安装案例
  • HV-1000A(配图像处理系统)显微硬度计安装
  • SQ-80型金相切割机
  • HVS-50型数显维氏硬度计安装实例
  • HV-1000ASCCT图像处理显微硬度计的安装
  • HV-1000ACCT显微硬度计图像处理系统安装
  • HTS-1000AG型数显里氏硬度计案例
  • MRG-480型三目倒置金相显微镜图像处理系
  • 4XCCCT金相图像处理显微镜案例
  • 安装调试4XCCT金相显微镜图像处理系统
  • HV-1000ACCT图像处理显微硬度计现场安装
  • HVG-30维氏硬度计安装实例
  • MRG-480型高品质三目倒置金相显微镜图像
  • 联系我们

    莱州市试验机金刚石工具厂

    厂家电话:0535-2215886

    0535-2263683

    0535-2265113

    华东分部:0571-85375562

    外贸联系:13693019205

    行业信息

    当前位置:网站首页 > 新闻资讯 > 行业信息

    • 硬度(洛氏布氏维氏里氏硬度)概述
    • 本站编辑:莱州市试验机金刚石工具厂发布日期:2019-10-11 16:18

     【硬度概述】  

        材料局部抵抗硬物压入其表面的能力称为硬度。试验钢铁硬度的最普通方法是用锉刀在工件边缘上锉擦,由其表面所呈现的擦痕深浅以判定其硬度的高低。这种方法称为锉试法这种方法不太科学。用硬度试验机来试验比较准确,是现代试验硬度常用的方法。常用的硬度测定方法有布氏硬度、洛氏硬度和维氏硬度等测试方法  

        布氏硬度以HB[N(kgf/mm2)]表示(HBS\HBW)(参照GB/T231-1984),生产中常用布氏硬度法测定经退货、正火和调质得刚健,以及铸铁、有色金属、低合金结构钢等毛胚或半成品的硬度。

        洛氏硬度可分为HRA、HRB、HRC、HRD四种,它们的测量范围和应用范围也不同。一般生产中HRC用得最多。压痕较小,可测较薄得材料和硬得材料和成品件得硬度。  

        维氏硬度以HV表示(参照GB/T4340-1999),测量极薄试样。  

        一、钢材的硬度  :金属硬度(Hardness)的代号为H。按硬度试验方法的不同,  

        常规表示有布氏(HB)、洛氏(HRC)、维氏(HV)、里氏(HL)硬度等,其中以HB及HRC较为常用。  

        HB应用范围较广,HRC适用于表面高硬度材料,如热处理硬度等。两者区别在于硬度计之测头不同,布氏硬度计之测头为钢球,而洛氏硬度计之测头为金刚石。  

        HV-适用于显微镜分析。维氏硬度(HV)  以120kg以内的载荷和顶角为136°的金刚石方形锥压入器压入材料表面,用材料压痕凹坑的表面积除以载荷值,即为维氏硬度值(HV)。  

        HL手提式硬度计,测量方便,利用冲击球头冲击硬度表面后,产生弹跳;利用冲头在距试样表面1mm处的回弹速度与冲击速度的比值计算硬度,公式:里氏硬度HL=1000×VB(回弹速度)/  VA(冲击速度)。便携式里氏硬度计用里氏(HL)测量后可以转化为:布氏(HB)、洛氏(HRC)、维氏(HV)、肖氏(HS)硬度。或用里氏原理直接用布氏(HB)、洛氏(HRC)、维氏(HV)、里氏(HL)、肖氏(HS)测量硬度值。  

        二、HB  -  布氏硬度:  布氏硬度(HB)一般用于材料较软的时候,如有色金属、热处理之前或退火后的钢铁。洛氏硬度(HRC)一般用于硬度较高的材料,如热处理后的硬度等等。  

        布式硬度(HB)是以一定大小的试验载荷,将一定直径的淬硬钢球或硬质合金球压入被测金属表面,保持规定时间,然后卸荷,测量被测表面压痕直径。布式硬度值是载荷除以压痕球形表面积所得的商。一般为:以一定的载荷(一般3000kg)把一定大小(直径一般为10mm)的淬硬钢球压入材料表面,保持一段时间,去载后,负荷与其压痕面积之比值,即为布氏硬度值(HB),单位为公斤力/mm2  (N/mm2)。  

        三、洛式硬度是以压痕塑性变形深度来确定硬度值指标。以0.002毫米作为一个硬度单位。当HB>450或者试样过小时,不能采用布氏硬度试验而改用洛氏硬度计量。它是用一个顶角120°的金刚石圆锥体或直径为1.59、3.18mm的钢球,在一定载荷下压入被测材料表面,由压痕的深度求出材料的硬度。根据试验材料硬度的不同,分三种不同的标度来表示:  

        HRA:是采用60kg载荷和钻石锥压入器求得的硬度,用于硬度极高的材料(如硬质合金等)。  

        HRB:是采用100kg载荷和直径1.58mm淬硬的钢球,求得的硬度,用于硬度较低的材料(如退火钢、铸铁等)。  

        HRC:是采用150kg载荷和钻石锥压入器求得的硬度,用于硬度很高的材料(如淬火钢等)。  

        【另外】  

        1.HRC含意是洛式硬度C标尺,  

        2.HRC和HB在生产中的应用都很广泛  

        3.HRC适用范围HRC  20--67,相当于HB225--650  

        若硬度高于此范围则用洛式硬度A标尺HRA。  

        若硬度低于此范围则用洛式硬度B标尺HRB。  

        布式硬度上限值HB650,不能高于此值。  

        4.洛氏硬度计C标尺之压头为顶角120度的金刚石圆锥,试验载荷为一确定值,中国标准是150公斤力。布氏硬度计之压头为淬硬钢球(HBS)或硬质合金球(HBW),试验载荷随球直径不同而不同,从3000到31.25公斤力。  

        5.洛式硬度压痕很小,测量值有局部性,须测数点求平均值,适用成品和薄片,归于无损检测一类。布式硬度压痕较大,测量值准,不适用成品和薄片,一般不归于无损检测一类。  

        6.洛式硬度的硬度值是一无名数,没有单位。(因此习惯称洛式硬度为多少度是不正确的。)  

        布式硬度的硬度值有单位,且和抗拉强度有一定的近似关系。  

        7.洛式硬度直接在表盘上显示、也可以数字显示,操作方便,快捷直观,适用于大量生产中。  

        维式硬度需要用显微镜测量压痕直径,然后查表或计算,操作较繁琐。  

        8.在一定条件下,HB与HRC可以查表互换。其心算公式可大概记为:1HRC≈1/10HB。  

        硬度试验是机械性能试验中最简单易行的一种试验方法。为了能用硬度试验代替某些机械性能试验,生产上需要一个比较准确的硬度和强度的换算关系。实践证明,金属材料的各种硬度值之间,硬度值与强度值之间具有近似的相应关系。因为硬度值是由起始塑性变形抗力和继续塑性变形抗力决定的,材料的强度越高,塑性变形抗力越高,硬度值也就越高。

    Overview of hardness

    The ability of a material to resist locally pressing a hard object into its surface is called hardness. The most common way to test the hardness of steel is to use a file on the edge of the workpiece. This method is called filing and it's not very scientific. It is a common method to test hardness with hardness tester. Common hardness measurement methods include brinell hardness, rockwell hardness and vickers hardness

    Brinell hardness is expressed as HB[N(KGF /mm2)] (HBS\HBW) (referring to GB/ t231-1984). Brinell hardness method is often used in production to determine the hardness of hair embryo or semi-finished products after return, normalizing, tempering and hardening, as well as cast iron, nonferrous metal, low-alloy structural steel, etc.

    Rockwell hardness can be divided into four types: HRA, HRB, HRC and HRD. HRC is most commonly used in production. Small indentation, can measure the hardness of thin and hard materials and finished parts.

    Vickers hardness is expressed as HV (reference GB/ t4340-1999) and extremely thin samples are measured.

    Hardness of steel: the code name of Hardness of metal is H. Depending on the hardness test method,

    Conventional expressions include brinell's (HB), rockwell's (HRC), vickers' (HV), and Richter's (HL) hardness, among which HB and HRC are more commonly used.

    HB has a wide range of applications, and HRC is suitable for surface materials with high hardness, such as heat treatment hardness. The difference is that the head of a brinell durometer is a steel ball, while that of a rockwell durometer is a diamond.

    HV- is suitable for microscopic analysis. Vickers hardness (HV) is pressed into the surface of the material with a load of less than 120kg and a diamond square cone press with a top Angle of 136°. The surface area of the indentation pit of the material is divided by the load value, which is vickers hardness value (HV).

    HL portable durometer, easy to measure, using impact ball head impact hardness surface, resulting in bounce; Hardness was calculated by using the ratio between the springback velocity and impact velocity of the punch at a distance of 1mm from the surface of the sample. The formula was: Richter hardness HL=1000×VB (springback velocity)/VA (impact velocity). Portable Richter hardness tester with Richter (HL) measurement can be converted into: brinell (HB), rockwell (HRC), vickers (HV), shore (HS) hardness. Or the hardness value can be measured directly by brinell's (HB), rockwell's (HRC), vickers' (HV), Richter's (HL) and shore's (HS) by Richter's principle.

    2. Hb-brinell hardness: brinell hardness (HB) is generally used when materials are softer, such as nonferrous metals, pre-heat treatment or annealed steel. Rockwell hardness (HRC) is generally used for materials with higher hardness, such as hardness after heat treatment, etc.

    Cloth hardness (HB) is to press a certain diameter of hardened steel ball or cemented carbide ball into the surface of the measured metal under a certain size of test load, keep it for a specified time, then unload and measure the indentation diameter of the measured surface. The distribution hardness is the quotient of the load divided by the surface area of the indentation. Generally, a hardened steel ball of a certain size (generally 10mm in diameter) is pressed into the material surface with a certain load (generally 3000kg) and kept for a period of time. After unloading, the ratio of the load to the indentation area is brinell hardness value (HB), which is expressed as kilogram force /mm2 (N/mm2).

    Iii. Rockwell hardness is determined by the depth of indentation plastic deformation. Take 0.002 mm as a hardness unit. When HB>450 or samples are too small, brinell hardness test should not be used instead of rockwell hardness measurement. It USES a diamond cone with a top Angle of 120° or a steel ball with diameters of 1.59 and 3.18mm to press into the surface of the measured material under a certain load, and then calculates the hardness of the material by the depth of indentation. According to the hardness of the test material, it can be expressed in three different scales:

    HRA: hardness obtained with 60kg load and drill cone presser, used for extremely hard materials (such as cemented carbide, etc.).

    HRB: hardness obtained by using 100kg load and 1.58mm diameter hardened steel ball, used for materials with lower hardness (such as annealed steel, cast iron, etc.).

    HRC: hardness obtained with 150kg load and drill cone presser, used for materials with high hardness (such as quenched steel, etc.).

    "The other"

    1.HRC means luo hardness scale C,

    2.HRC and HB are widely used in production

    3. Applicable scope of HRC: HRC 20--67, equivalent to HB225--650

    If the hardness is higher than this range, use luo hardness A scale HRA.

    If the hardness is lower than this range, use luo hardness B scale HRB.

    The upper limit of cloth hardness is HB650, which cannot be higher than this value.

    4. The pressure head of rod C of rockwell durometer is a diamond cone with a top Angle of 120 °. The test load is a definite value. The pressure head of a brinell durometer is a hardened steel ball (HBS) or carbide ball (HBW), and the test load varies with the ball diameter, from 3000 to 31.25 kg.

    5. Luo hardness indentation is very small, the measured value is local, need to measure the number of points for the average value, applicable to finished products and flakes, belong to the category of NDT. The cloth hardness indentation is large, the measured value is accurate, not suitable for finished products and flakes, generally does not belong to the category of NDT.

    6. The hardness value of luo type hardness is zero, no unit. (so it is not correct to use the term luo hardness.)

    The hardness value of the cloth hardness has a unit, and there is a certain approximate relationship with the tensile strength.

    7 luo hardness directly on the dial display, can also be digital display, easy to operate, fast and intuitive, suitable for mass production.

    D hardness need to use a microscope to measure the indentation diameter, and then look up the table or calculation, the operation is more complicated.

    8. Under certain conditions, HB and HRC can be interchanged by table lookup. Its mental formula can be roughly written as: 1HRC≈ 1/10hb.

    Hardness test is the most simple and feasible test method in mechanical property test. In order to replace some mechanical property tests with hardness tests, a more accurate conversion between hardness and strength is needed in production. Practice has proved that there is an approximate and corresponding relationship between the hardness values of metal materials and the hardness and strength values. Because the hardness value is determined by the initial plastic deformation resistance and the continuing plastic deformation resistance, the higher the strength of the material, the higher the plastic deformation resistance, the higher the hardness value.